7 steps to change a roller shutter cord
If there is one thing that characterises the alicantine blinds is that they are very easy to use and never go out of fashion, especially in those areas closest to the Mediterranean Sea. The problem is arises when its tape breaksTherefore, in this post we are going to show you how to change the cord of an alicantina blind.
Necessary elements to change a cord of an alicantine shutter
The alicantine blinds are characterised because they work by pulling a cord that is responsible for collecting the slats and winding them on itself; its purpose is to protection from the sun and flies inside the home. Due to their simple appearance and operation, they are the most economical option.
The problem arises when the roller shutter cord breaks; as you can see, this element is a very important part of the blind. essential for it to perform its function. Therefore, as soon as this pulley is damaged, it has to be replaced.
Below we show you all the tools you have to use to change the cord of your alicantina blind:
- Pliers or spanner.
- Hammer.
- Medium flat-blade screwdriver.
- Lighter.
- Quality rope. It should measure 3 times the length of the blind and should ideally be made of nylon.
Steps to follow
Although it may seem complicated, replacing the cord of a roller shutter with a new one is a fairly simple and time-saving process; below we show you how to replace the cord with a new one. steps you have to follow for the final result to be a success:
- Roll up the blind and unhook it from the hooks.If it is installed on the outside, it will be on the eyebolts and if it is on the inside, on the eyebolts or open eyebolts. To be able to unhook it, you must roll it up and turn your wrists a little more until it unhooks.
- Place the blind on a flat, wide, horizontal surface.unwind the front side and locate the part where the staples hold the rope, also called upright.
- Lift the staples with pliers.If you are not strong enough, you can use a screwdriver and then remove them with pliers. Also, be careful when removing them not to break them, so that you can reuse them.
- Analyse how the rope is installed before removing it.The best thing to do is to take a photo so that when you go to fit the new one, you can do so without any problem.
- Cut the ropeIt is possible that you have some rope left over and you need to cut it; you can do it. All you have to do is burn the ends with a lighter when you're done, to avoid fraying.
- Put the ends with the ends with the ends of the ends in a balled up positionRe-insert the staples with short, precise strokes until the end is secure. If necessary, use a hammer to do this.
- Turn the alicantina blind with the cord: pass the other end through the pulley.
- Roll up the blindThe time has come to reinstall it. To do this, the knob must face inwards, never outwards.
Tips for assembling and hanging your alicantine shutters
As you have been able to see, changing the cord of an alicantina blind is very quick and easy; even so, below we give you some tips on how to change the cord. tips that can help you to install it again.
- Look at the top of the roller blind to know the exact position of the eyebolts. To do this, you have to divide it into 4 equal parts and install 1 eyebolt at a quarter distance from each end.
- Installation inside the shaftYou should use closed eyebolts for the back of the upright and open sockets for the studs.
- Wall-mounted installationYou have to use pliers.
No matter whether you live on the Mediterranean coast or not, the Alicante shutter is always a good way to regulate the light input and, at the same time, maintain a certain degree of privacy in the home.
As you can see, changing the cord of an alicantina blind is very simple and will help you to enjoy your curtain for much longer. Also, if you don't have them yet, don't hesitate, it will give you many benefits and its maintenance is very quick and easy.
Keep your roller shutter intact over time and keep your home cool in summer and warm in winter.