How to fix a fallen shutter

If you are here, it is because when you tried to lower your shutter it fell down. At first it can be seen as a rather cumbersome process and we are left at a dead end; however, with 24H Systems you will learn how to fix it with a few simple steps.

The shutters are protect against climatic factorsSo when it breaks down, we need a lot of it. That's why we've gathered all the information you need. In this article we tell you about the possible corrections you can make at home.

What materials and tools do I need?

The first thing we will do is a diagnosisThe reason for this is that we cannot act unless we are clear about what needs to be repaired and how it is to be repaired. For example, you may need a new belt, or you may need to replace the shaft supports because you are not sure what needs to be repaired. over time they deteriorated.

But, in order to make a general maintenance we will need the following materials:

• Unused tape collector.
• Unused trim.
• Lamas.
• Rag.
• Tape runners.
• Shutter stops

And as for the tools:

• Phillips screwdriver, also flat.
• Electric screwdriver.
• Tongs.
• Scissors.
• Blade.

Steps to fix a blind that won't go up

1. As a fundamental first step, we will carry out a diagnosis; to do this, it will be of utmost importance that we let's remove the cover of the roller shutter drawer.. This step can be carried out with force, if it is pressurised, or with a screwdriver if it has screws.
2. We move the blind away from the outside, so that it will be more visible inside and we can easily distinguish the origin of the conflict by looking through its pieces. After this we can distinguish whether it is replacement is necessarywhich it probably will, so that it can regain its usefulness.
3. Remove the dustpan with a screwdriver, make sure you store the screws in a place within easy reach, as we will need them to close the process.
4. From this point, we will begin to replace the previous tape for a new one.
5. Pull out the entire belt, so that it comes out from the shaft.
6. Now it is time to study whether there is a gap.
7. These opportunities are good for apply a cleaning product to literally make your roller shutter as good as new. You can do this by removing the shaft where the blind is stored.
8. You can also replace axle stands that have been in use for a long time. Use the screwdriver to fix them right where the previous ones were.

In case the slat is broken or deteriorated

The lama is a essential element that makes up the window and is exposed to all weather and temporary events so that they do not reach your home. The quality of the slat is what defines the quality of the blind The most important part of the system, in addition to those that make its mechanisms possible, is therefore the whole of the system.

For change it you just have to:

1. Identify the slat in poor condition.
2. Take it out.
3. Select the new slat that you purchased and replace the previous one with this one, just insert it carefully.
4. The process gets a little complicated when the deteriorated slat is the one found at the end of the shutter; If this is the case, you must remove all the components that make it up. Once this step has been completed, mark the new strips or tapes to be placed on the new plank with anything you can find.

You can guide in the structure of the previous plank to do the job better.

In case you need to add a new ribbon picker

We must emphasise that during this renovation process is the time when you should take the opportunity to replace the parts of your roller shutter that are deteriorated, doing this work in one go. will save you time and money in the long run..

1. Place the new tape inside the dustpan even before it enters the shutter.
2. The place where the ribbon will pass through in all its splendour will be the ribbon pass-through. Make sure it is in the correct orientation or these steps will not make your blind work again.
3. Fold the tape at the end and cut a little in the middle leaving a small hole.
4. It uses the pulley as a method of sensing whether the picker has been properly installed. The way to do this is to grip it with pressure to prevent it from slipping out and damaging the condition of your hand.
5. Take a good look at the pulley, you will see that in one part it has a metal protrusion or screw and in this case just install the tape on the correct side.
6. Now, little by little, let the belt takes its place on the pulley. 
7. When it does screw.
8. From this point onwards, also look at the window stopsIf they are old or damaged, replace them immediately.
9. Finally, put everything back as it was.